Will this cut 5/8" G00 chain? View answer
Answer posted 3 years ago | HIT Hydraulic Wire Rope Cutter - 1-7/8" Max Cut - #22-HCC48N
4.78 pounds each boot or as a pair? View answer
Answer posted 3 years ago | Danner Pronghorn 8" Calk Logger Boot by Hoffman
What size nuts are used on the bolt? View answer
Answer posted 3 years ago | Crosby 1-1/8" G-450 Wire Rope Clip - #1010257
Which lock would be recommended with this chain? View answer
Answer posted 3 years ago | Peerless 7/16" (11mm) Hex Security Chain
Do they fit Bashlin aluminum climbers? View answer
Answer posted 3 years ago | Opsal Aluminum Climber Pads
We have an enclosed trailer that was modified to haul classic cars. The rear ramp, modified with steel and 3/4 plywood, weighing about 800 lbs., is raised and lowered by a 2500 lb. winch. 5/16 cable runs over a 2" pulley suspended at the ceiling, just inside the door. After only about 20 open/close cycles, at a point EXACTLY 10 inches up from the thimble where cable attaches to the ramp, the "core" stand of the cable begins to protrude about a 1/2 inch. I tried steel, stainless, and galvanized; always happens in the same spot, same time frame! Any ideas why? I've cut 16" off the end, replace thimble and clamps, and it happens again! View answer
Answer posted 3 years ago | 5/16" 7x19 Stainless Steel Aircraft Cable - 9000 lbs Breaking Strength
What size should the rectangle be cut into the road plate to work with this clamp? View answer
Answer posted 3 years ago | ADB Fast-Lok Plate Tool
Hi, I work in a AHTS vessel. We use this 120 tons shackels, that has xxxx and bolt and a hole for safety pin, and I see the crew tight the bolt with a hammer and put the pi9n inside the hole, use a couple of bars to bend every leg of the pin and the use a hammerto bend more>my question is if is ok to use the hammer or is useful, , I think the hammer is unnesesary but I want to double check with you, regards David G. View answer
Answer posted 3 years ago | Crosby 3-1/2" G-2130 Bolt Type Anchor Shackle - 120 Ton WLL - #1019739
Do you have this in stock? View answer
Answer posted 3 years ago | Notch Sentinel Tree Saddle - Size 1 (28" - 36")
Is this galvanized steel? View answer
Answer posted 3 years ago | Chicago 1-1/2" Tap Heavy-Duty Eye Nut - 35600 lbs WLL
Can I use this to clean palm trees? View answer
Answer posted 3 years ago | WRS Basic Tree Climbing Kit w/ Spurs
Do you sell replacement scabbards for the C-400-LH Ichigeki saw? View answer
Answer posted 3 years ago | Samurai Sumo 16" Curved Saw
Does "Reach B-B" equal to the length of each bridle? View answer
Answer posted 3 years ago | Junkin 4-Leg Nylon Stretcher Bridle Sling
What is the country of origin? Where is it made? View answer
Answer posted 3 years ago
Are these Chinese made? View answer
Answer posted 3 years ago | 3/8" Blue Line Thimble w/ Gusset
Does this have have any sort of brake in it? If I tie in to a tree top to pull it over I normally get the rope taught, make my notch., then tighten up for the final pull. I'd hate to tighten up and it loosen up while I'm making my notch. Also, the batteries look to match my Stihl batteries. Are they interchangeable? View answer
Answer posted 3 years ago | Portable Winch Battery Powered Capstan Winch Kit w/ Batteries - 2200 lbs Max Pull
How do I order online? View answer
Answer posted 3 years ago | Fiskars 28" Hookaroon
Does the capspan winch come with the drive chain? View answer
Answer posted 3 years ago
hi we are need shank hook for 25 ton. Do you have ? View answer
Answer posted 3 years ago | Crosby S-319A 45 Ton Alloy Shank Hook - #1024885
I plan on anchoring a 40 foot container on each corner and pouring 20 inches thick concrete with the shaft of the anchor running through the concrete and then welding a plate of steel to the shaft then welding the container to the plate. The anchor would be going straight down. Would this work? View answer
Answer posted 3 years ago | 1" x 8" x 66" Helical Auger Anchor - 11000 lbs Max Capacity
Is this forged in USA View answer
Answer posted 3 years ago | Phoenix Double Bit Axe - 36" Hardwood Handle
I install Safes for a living and sometimes have to go down Bilco doors with Safes anywhere between 800 pounds and 1500 pounds and I hate having guys at the bottom because its dangerous. Can these anchors be used to hold back the safe as it goes down? View answer
Answer posted 3 years ago | Duckbill 68-RBK Rootball Anchor Kit - 1100 lbs Capacity
Is there any way to get just the springs? View answer
Answer posted 3 years ago | CM 3/8" Latch Kit for Clevis Sling Hook
Would this work for a tow cable? View answer
Answer posted 3 years ago | 1-3/8" 6x26 Swaged Wire Rope - 222000 lbs Breaking Strength
Is this American made? View answer
Answer posted 3 years ago | 8" Snatch Block w/ Hook - 15 Ton WLL
Does it comes with engine ready to use? View answer
Answer posted 3 years ago
Is the binder US made? View answer
Answer posted 3 years ago | Peerless QuikBinder + 3/8" Grade 80 Tie Down Chain
When is item going to be available for shipping? View answer
Answer posted 3 years ago | Weaver Synthetic Chainsaw Tool & Wedge Pouch
Why is this item not considered a lifting device? View answer
Answer posted 3 years ago | 3/8" x 10 ft Cat Choker w/ Eye - 11000 lbs Breaking Strength
For length is this overall or from hole center? View answer
Answer posted 3 years ago | Crosby SS-4055 5TC & 7TA Latch Kit - #1090107
Is the flag double sided with the Tree Work Ahead verbiage? View answer
Answer posted 3 years ago | Notch 36" Tree Work Ahead Sign & Stand Combo
Do you have a 250ft throw line for the Forester throw weight kit with bag? View answer
Answer posted 3 years ago | Forester Throw Weight Kit w/ Bag
Is this made with stainless steel wire rope? View answer
Answer posted 3 years ago | 1/4" x 5 ft QOS 4-Leg Wire Rope Bridle Sling - 4400 lbs WLL
Do you have a welding shield to fit your helmet? View answer
Answer posted 3 years ago | Kask Zenith X Air Helmet Combo Kit - Black
Can you please tell me the WLL of this product? I do not see it in the description. View answer
Answer posted 3 years ago