Is this made in the USA? View answer
Asked 6 ´years ago
What is the length of a leg? View answer
Asked 6 ´years ago | Junkin 4-Leg Nylon Stretcher Bridle Sling
What are the dimensions of this latch? View answer
Asked 6 ´years ago | Johnson A-7 Complete J-Latch Kit - #471783
What is meant by 3/4"? View answer
Asked 6 ´years ago | 3/4" Alloy Steel Pear Link - 12300 lbs WLL
How long is the rope in this kit? View answer
Asked 6 ´years ago | WRS Deluxe Tree Climbing Kit
Because this rod is threaded, there is no spacer washers needed View answer
Asked 6 ´years ago
I am looking for approximately 2000 of the A-1337 Lok-A-Loy Grade 100 Coupling Links. We are still determining the size of chain we will be using, however I was wondering if these are sold individually or in packages (and if in packages what the quanitty size is of the 9/32, 5/16 and 3/8"). View answer
Asked 6 ´years ago | Crosby 9/32" (1/4") A-1337 Lok-A-Loy Grade 100 Coupling Link - 4300 lbs WLL - #1015104
Can the swivel lift hoist ring be used with drilled and grouted thread rod and nuts instead the Allen bolt which threads into a cast insert as suggested in the catalog cuts? I presume the hoist ring itself is not threaded but smooth such that it slides over the Allen bolt or thread rod. View answer
Asked 6 ´years ago | Crosby 1"-8 x 1.14" HR-125UNC Swivel Hoist Ring - 10000 lbs WLL - #1016964
I would like to get two of these items. So, two 1/2" Laclede 5 foot chains each with a Padlock. I would like to have them keyed to the same key if possible. I'd also like a sleeve, but i'm confused what the difference is between the sleeves that are shown. I'd like it to be a nice firm fit on the chain - which would be the best? View answer
Asked 6 ´years ago
How long is the boom in inches? View answer
Asked 6 ´years ago
Is this unit approved by OSHA? View answer
Asked 6 ´years ago | Crosby IP IP10 1 Ton Lifting Clamp - #2701662
I have a concern with a crane on our project using a wedge socket upside down. I have never seen someone use it in this manner. I was checking to see if this was an ok practice or if it was against manufacturers recommendations. There are two systems on this crane, one right side up and the other upside down. Any advice or knowledge on this matter is appreciated.Glen View answer
Asked 6 ´years ago | Crosby 5/8" S-421T Terminator Wedge Socket - #1035018
I have a concern with a crane on our project using a wedge socket upside down. I have never seen someone use it in this manner. I was checking to see if this was an ok practice or if it was against manufacturers recommendations. There are two systems on this crane, one right side up and the other upside down. Any advice or knowledge on this matter is appreciated.Glen View answer
Asked 6 ´years ago | Crosby 5/8" S-421T Terminator Wedge Socket - #1035018
I have a concern with a crane on our project using a wedge socket upside down. I have never seen someone use it in this manner. I was checking to see if this was an ok practice or if it was against manufacturers recommendations. There are two systems on this crane, one right side up and the other upside down. Any advice or knowledge on this matter is appreciated.Glen View answer
Asked 6 ´years ago | Crosby 5/8" S-421T Terminator Wedge Socket - #1035018
I have a concern with a crane on our project using a wedge socket upside down. I have never seen someone use it in this manner. I was checking to see if this was an ok practice or if it was against manufacturers recommendations. There are two systems on this crane, one right side up and the other upside down. Any advice or knowledge on this matter is appreciated.Glen View answer
Asked 6 ´years ago | Crosby 5/8" S-421T Terminator Wedge Socket - #1035018