Westech Rigging Supply Q&AWhat brand is your xxxx block? View answer
Asked 4 ´years ago | 6" Snatch Block w/ Hook - 8 Ton WLL
What is the Working Load Limit formula for the UHMWPE rope? View answer
Asked 4 ´years ago
What is the minimum load requirement for this clamp? I would be using this clamp to habitually lift 3/8" thick steel plate that weighs between 375 and 400 lbs in a 36" x 98" sheet. Since it is advisable for safety and longevity of the clamp to lift as close to the max capacity as possible, if this clamp will not work, do you have another model # that will? View answer
Asked 4 ´years ago | AMH 1 Ton Vertical Plate Lifting Clamp - #PCUA010
Asked 4 ´years ago | MSA HPE Cap-Mounted Ear Muffs - NRR 27 dB - #10061272
What is the weight capacity? View answer
Asked 4 ´years ago | Gunnebo UKN 1 Ton Weld-on Bucket Hook - #Z6511810
How thick is the material on this cone? View answer
Asked 4 ´years ago | Portable Winch Skidding Cone for Logs
To drive a Duckbill Anchor to the full depth of its cable, would you not need a drive rod at least a little bit longer than the cable? Which is to say, how for an 88-DB1 Anchor, which is shown as having a 3.5' cable, can one properly drive it with a DS-68 Rod, which is listed at 36" long (and is described as being used with the 88 Anchor)? Thank you. View answer
Asked 4 ´years ago | Duckbill 88-DB1 1/4" x 3.5 ft Earth Anchor - 3000 lbs Capacity
Can you get this item with a 1 inch wide jaw ? I need a turnbuckle that is no longer than eleven inches closed that will go over a one inch wide d ring and hold minimum of 500 lbs safe load that is made in america that i can get load test certs with. View answer
Asked 4 ´years ago | Chicago 1/2" x 2" Forged Jaw & Jaw Turnbuckle - 2200 lbs WLL
Is this USA made or other? View answer
Asked 4 ´years ago | 1/2" Forged D-Ring & Weld-on Clip - 4000 lbs WLL
What is the circumference of the silver rings? View answer
Asked 4 ´years ago
Are the roller bearings replaceable? View answer
Asked 4 ´years ago | 6" Yarding Block w/ Fixed Bail - 6 Ton WLL
Where is this item manufactured? View answer
Asked 4 ´years ago | Durabilt 5/16" - 3/8" Lever Binder - 7100 lbs WLL
Do they fit Bashlin aluminum climbers? View answer
Asked 4 ´years ago | Opsal Aluminum Climber Pads
We have an enclosed trailer that was modified to haul classic cars. The rear ramp, modified with steel and 3/4 plywood, weighing about 800 lbs., is raised and lowered by a 2500 lb. winch. 5/16 cable runs over a 2" pulley suspended at the ceiling, just inside the door. After only about 20 open/close cycles, at a point EXACTLY 10 inches up from the thimble where cable attaches to the ramp, the "core" stand of the cable begins to protrude about a 1/2 inch. I tried steel, stainless, and galvanized; always happens in the same spot, same time frame! Any ideas why? I've cut 16" off the end, replace thimble and clamps, and it happens again! View answer
Asked 4 ´years ago | 5/16" 7x19 Stainless Steel Aircraft Cable - 9000 lbs Breaking Strength
Is this galvanized steel? View answer
Asked 4 ´years ago | Chicago 1-1/2" Tap Heavy-Duty Eye Nut - 35600 lbs WLL
Hi, I work in a AHTS vessel. We use this 120 tons shackels, that has xxxx and bolt and a hole for safety pin, and I see the crew tight the bolt with a hammer and put the pi9n inside the hole, use a couple of bars to bend every leg of the pin and the use a hammerto bend more>my question is if is ok to use the hammer or is useful, , I think the hammer is unnesesary but I want to double check with you, regards David G. View answer
Asked 4 ´years ago | Crosby 3-1/2" G-2130 Bolt Type Anchor Shackle - 120 Ton WLL - #1019739
Do you have this in stock? View answer
Asked 4 ´years ago | Notch Sentinel Tree Saddle
What size nuts are used on the bolt? View answer
Asked 4 ´years ago | Crosby 1-1/8" G-450 Wire Rope Clip - #1010257
Can I use this to clean palm trees? View answer
Asked 4 ´years ago | WRS Basic Tree Climbing Kit w/ Spurs
What is the country of origin? Where is it made? View answer
Asked 4 ´years ago
